May 2020 | Xi Xiong, Ph.D., and Stephen H. Anderson, Ph.D.
Filed to: Wetting agents, Soil primer adhesion promoter
Pressure chamber systems used for water retention measurement. Photo by Stephen Anderson
Editor’s note: This research was funded in part by GCSAA through the Environmental Institute for Golf.
For many of us, wetting agents are common tools we use for the purposes of conserving irrigation water and/or managing soil water repellency. It has been estimated that, on average, the U.S. golf industry uses more than 2 billion gallons of irrigation water on a daily basis, and wetting agents are the No. 1 measure adopted by 92% of golf facilities for water management (18).
On golf courses, especially on sand-based growing mediums such as USGA greens, soil water repellency is, unfortunately, an inevitable condition. Although soil water repellency can occur on all soil types, coarser particles, such as the sands used to build and/or topdress greens, are more susceptible to the development of water repellency because they have a significantly smaller (>105 times) specific surface area (area/mass) compared with peat and clay (3).
It is also argued that the significantly smaller specific surface area, along with the higher distribution of macropores found in sandy soils, provides a preferred habitat for fungal growth rather than bacteria, further promoting the development of soil water repellency (8). Consequently, water bypasses repellent areas and forms preferential flow, leading to the development of localized dry spot. Regardless of management intensity, water repellency will eventually develop, and localized dry spot may be observed on sand-based greens as soon as six months after construction (19).
Water repellency, or hydrophobicity, is a phenomenon in which a surface repels water into individual droplets, thus inhibiting water infiltration into porous mediums such as soil. This repelling force is caused by strong cohesion within the water body, which is termed “surface tension” or “surface-free energy.”
Under normal conditions (68 F; 20 C), surface tension of water is 72.75 millinewtons/meter (15). Surfaces with a surface-free energy greater than 72.75 millinewtons/meter possess stronger adhesive forces than the cohesive force within water, which forces attraction with contacting water molecules and spreads them over the surfaces, sequentially retaining water and forming hydrophilic surfaces.
When a soil medium becomes hydrophobic because of an accumulation of organic acids, its surface-free energy decreases to below 72.75 millinewtons/meter, resulting in a failed attraction to bypass water molecules and, inevitably, the development of water repellency. Addition of wetting agents — amphiphilic molecules with hydrophobic tails and hydrophilic heads in their chemical structures — reduces the surface tension of water and simultaneously allows the wetting agents to pass into the soil, thereby increasing infiltration and water retention (17).
Since the development of the first patented wetting agent product — a blend of nonionic surfactants such as alkylphenol ethoxylate (6) — and the early research that investigated soil water repellency on turf in the 1960s (13), tremendous advances have been made in various wetting agents that include formulations with ethylene oxide and propylene oxide block copolymers (1, 2, 7), for the purposes of increasing water infiltration, promoting homogeneous soil moisture and, if possible, preventing the development of soil water repellency. Performance of those wetting agents, however, is dramatically influenced by formulations, application rates and environmental conditions (5, 12). This article, therefore, aims to summarize some of our recent research findings regarding inherent differences among wetting agents and, we hope, provide guidance in selecting the appropriate wetting agents to meet various goals.
As described above, adding wetting agents can reduce the surface tension of water, allowing the wetting agents to enter the hydrophobic soil medium and thereby facilitate infiltration. In this laboratory-based experiment, 15 commonly used wetting agents in the turf market (see the 15 products in Table 1) were mixed with water at five rates — 4, 2, 1, 0.5 and 0.25 times the rates suggested on the label — before determining their surface tension using the Attention Theta Lite tensiometer (Biolin Scientific). This experiment was designed as a completely randomized design with a factorial combination of wetting agents and various rates, with three replications and two repeats.
Figure 1. Distribution of surface tension (millinewtons/meter) of 15 wetting agents at 4, 2, 1, 0.5 and 0.25 times the label suggested rates.
These results suggested that all wetting agents tested, regardless of rates, substantially reduced the surface tension of water, indicating improved infiltration into a hydrophobic soil surface. We also saw a trend of lower surface tension generally being associated with higher concentrations of the same product. Our early research found a negatively correlated relationship between surface tension and hydraulic conductivity for a given wetting agent solution (17). Therefore, a wetting agent that produces relatively higher surface tension is likely to produce relatively lower infiltration into hydrophobic soil.
In the laboratory, six wetting agents were then tested for their effect on water infiltration into hydrophobic sands. The wetting agents selected were H2O Maximizer (KALO), TriCure AD (Mitchell Products), Capacity (Becker Underwood), Aqueduct (Aquatrols), Primer Select (Aquatrols) and InfilTRx (Aquatrols).
Sands that meet the USGA recommendation for green construction were treated with octadecylamine in the laboratory to create steady hydrophobicity at 7.2 molar (based on the molarity of ethanol droplet test) (11). This level of hydrophobicity is categorized as severely water-repellent (10). The sand was then packed uniformly in an infiltration system made of PVC pipes, and the infiltration of the selected wetting agents at their label-suggested rates was determined with the method described in our earlier publication (17). This experiment was a completely randomized design with three replications and one repeat.
Figure 2. Infiltration of six selected wetting agents into hydrophobic sand. The water-only treatment did not penetrate into the hydrophobic sand, hence its infiltration was not generated.
All wetting agents were tested at their highest label-suggested rates. Within 30 minutes after application and by 10 minutes into ponding, all the selected wetting agents reached a steady infiltration rate (Figure 2, above). The steady infiltration rates of Capacity and Aqueduct reached 1.06 inch (27 millimeters)/minute, while the other four products maintained a steady rate of 0.94 to 0.98 inch (24 to 25 millimeters)/minute. All the rates surpassed the minimum saturated hydraulic conductivity of 0.1 inch (2.5 millimeters)/minute recommended by the USGA for green construction. Under the testing conditions, tap water alone was not able to penetrate into this severely hydrophobic sand, hence no infiltration data are presented.
Water retention of a soil medium is highly influenced by soil physical and chemical properties, such as texture, porosity and organic matter content. When a wetting agent solution is introduced to a hydrophobic soil, its influence on soil water retention becomes a function of its chemical properties, specifically the balance between the hydrophobic and lipophilic regions, which is called the hydrophilic-lipophilic balance (16).
In this experiment, we first collected sands from a USGA green where localized dry spots had been documented. After removing plant debris, the sands were thoroughly mixed, bench-dried and stored for future use. Using the molarity of ethanol droplet test, we determined that the hydrophobicity of the sand was 3.4 molar, which is considered very severe (11). The organic matter of the sand was determined to be 1.73%. The particle analysis revealed that the sands consisted of 6.76% very coarse sand, 12.74% coarse sand, 58.73% medium sand, 20.75% fine sand and 1.02% very fine sand. At a bulk density of 0.86 ounce/cubic inch (1.49 grams/cubic centimeter), the total porosity of the sands was 43.9%, with 24.5% capillary porosity and 19.4% air-filled porosity.
The hydrophobic sands were then used in a pressure chamber experiment using porous plates containing sands that had previously been saturated with the 15 wetting agent solutions described above at the highest label rates. The pre-treated sands were subjected to pressure treatment at -0.42 psi (-2.9 kPa) for estimated field capacity and at -217.56 psi (-1,500 kPa) for permanent wilting point (14). For perspective, 1,500 kPa is equivalent to 15 times atmospheric pressure at sea level. After equilibration, the gravimetric water content corresponding to each pressure value was calculated and adjusted to volumetric water content. Plant-available water was then estimated by subtracting the lower limit (-217.56 psi, permanent wilting point) from the upper limit (-0.42 psi, field capacity) (4, 9). This experiment was arranged in a completely randomized design with four replications and one repeat.
Figure 3. Estimated plant-available water (%) of 15 wetting agents evaluated. Bars labeled with different letters are significantly different from one another.
It is important to emphasize that these results were based on the particular soil used in this experiment. Soils with different physical and chemical properties will most likely generate different amounts of water retention for a given wetting agent. Although not all wetting agents tested here are designed for water retention, our results also suggest that wetting agents vary substantially in their potential for retaining plant-available water and, therefore, for use in water conservation.
This article summarizes a few updates from our recent research on wetting agents and provides a glimpse of inherent differences among wetting agents because of their chemical properties. We believe we have provided strong evidence that not all wetting agents are created equal, and users should select the proper wetting agents discriminately based on their specific goals.
This material is based upon work that is partially supported by GCSAA and the National Institute of Food and Agriculture, U.S. Department of Agriculture, under award No. 1006256.
Xi Xiong is an associate professor in the Division of Plant Sciences, and Stephen H. Anderson is a William A. Albrecht Distinguished Professor of Soil and Environmental Sciences in the School of Natural Resources at the University of Missouri, Columbia, Mo.
Filed to: Wetting agents, Soil
Copyright 2025, all rights reserved. 1421 Research Park Drive, Lawrence, KS 66049
molding tape adhesion promoter Copyright 2025, all rights reserved. 1421 Research Park Drive, Lawrence, KS 66049