- Multiple connections allow a higher output, while the output adjustment function enables flexible power generation plans -
Pure Hydrogen Fuel Cell Generator “H2 KIBOU” Hydrogen Maker Machine
Osaka, Japan - Panasonic Corporation (hereinafter referred to as Panasonic) today announced that its Electric Works Company will launch a new pure hydrogen fuel cell generator that generates power through a chemical reaction between high-purity hydrogen and oxygen in the air in Oct. 2024 in Europe*1, Australia, and China.
In October 2021, Panasonic launched a 5 kW type pure hydrogen fuel cell generator PH1 (single-phase three-wire type). The company will now launch a new product PH3 (DC type) for overseas markets to fully scale up its hydrogen business outside Japan.
Since the PH3 to be launched is a cogeneration system, it can output a maximum of 10 kW of DC power, and generate approximately 8.2 kW of heat, which can be used to heat water to approximately 60ºC. The product is designed to output DC power in order to support power voltage in a wide variety of countries and areas. In addition to a higher output by connecting multiple units (up to 250 modules), the power output can be adjusted*2, allowing for the formulation of flexible power generation plans. Furthermore, maintenance access points are located in the front, and the product is designed to withstand cold temperatures, as well as high altitudes, enabling it to be proposed to customers with various installation environments. In addition, the product achieves an electrical efficiency of 57% (DC, LHV), heat recovery efficiency of 47% (LHV), and a total efficiency of 104%*3, contributing to reduced running costs. The overhaul stop period is designed to be 15 years to ensure a long operating life*4, which can reduce life cycle costs.
Panasonic, based on knowledge obtained through H2 KIBOU FIELD*5,6, the demonstration facility for RE100 solutions in Japan, plans to carry out similar demonstrations in its own factories in Wales, as well as in Germany.
Panasonic will offer a new option, full-scale use of hydrogen, in order to expand the introduction of renewable energy based on the Panasonic GREEN IMPACT formulated by the Group, contributing to the realization of a decarbonized society.
*1: The planned target markets are Germany, the UK, Belgium, Switzerland, France, Austria, Netherlands, Spain, and Italy.
*2: Power output can be set in 1 kW increments between 4 kW and 10 kW per module.
*3: The new product can recover condensation latent heat. Since its heat recovery rate includes condensation latent heat, its total efficiency is over 100%.
*4: The operating life is depended on customer’s power generation plan. (Whichever comes first energization time 15 years, cumulative hours of power generation 100,000 hours and cumulative start & stop cycle 4,500 times)
*5: The H2 KIBOU and H2 KIBOU logos have been registered as trademarks of Panasonic Corporation.
*6: In April 2022, Panasonic began operations at its RE100 solution demonstration facility in Japan, which generates 100% of the power used by its fuel cell factory from renewable resources using a self-sustaining power system that combines generation from both pure hydrogen fuel cell generators and photovoltaic generators. As a result, high environmental performance (a power purchase reduction rate of 98%) was achieved. Although hydrogen from renewable energy is not used during demonstration, Panasonic aims for the achievement of RE100 by using hydrogen derived from renewable energy in the future.
A pure hydrogen fuel cell generator PH3 can generate a maximum of 10 kW of DC power, as well as approximately 8.2 kW of heat through a chemical reaction between high-purity hydrogen and oxygen in the air. By connecting a hot water storage to the product, heat generated from the fuel cell can be converted into hot water (approx. 60ºC) for use in a factory or building.
By using the dedicated PH3 app, the power output can be adjusted in 1 kW increments between 4 kW and 10 kW per module. Since up to 250 pure hydrogen fuel cell generators can be connected, flexible power generation plans can be formulated for factories and buildings where various types of demand fluctuations are expected.
Screen for setting a power generation plan (1 module)
The PH3 can be installed even in small spaces, since the maintenance access points are located in the front*7. It can also be provided to a wide range of customers as it is resistant to cold (lower limit: -15ºC), as well as high altitude (1,000 m).
*7: Since installation regulations differ depending on the country, please confirm them before installation.
Installation examples for 40 kW power output (In case of without a design panel)
High efficiency rates such as an electrical efficiency of 57% (DC, LHV), heat recovery efficiency of 47% (LHV), and total efficiency of 104% have been achieved. High efficiency leads to reduced hydrogen usage, contributing to reduced running costs. The overhaul stop period is designed to be 15 years to ensure a long operating life*4, which can reduce life cycle costs.
Pure Hydrogen Fuel Cell Generator “H2 KIBOU”
Polymer Electrolyte Fuel Cell (PEFC)
Year and month of launch
Cogeneration system (external water-cooling system)
10 kW max. Adjustable in 1 kW increments between 4 and 10 kW
DC 380-495 V*8 (Fixed Voltage)
Water-cooling equipment is required (external procurement)
Hot water storage unit (external procurement)
30 sec (approx. 40 sec to achieve the rating)
W900 mm x D865 mm x H1,787 mm
W900 mm x D898 mm x H1,787 mm (with a design panel)
W957 mm x D966 mm x H1,917 mm
340 kg 354 kg (with a design panel)
360 kg (a design panel is 18 kg)
When up to 10 modules are connected*9
PH3 app (provided with PH3) (PH3 app is not required during EMS connection)
When up to 250 modules are connected (with PLC)*10
Front maintenance: 600 mm, Other: 10 mm *11,12
Required depending on cumulative hours of power generation
Cumulative hours of power generation 100,000 H
Cumulative start & stop cycle 4,500 times
*8: The inverter is required conforming to the application note.
*9: The computer used to install the app must be provided by the customer. The computer and fuel cell unit must be connected via LAN.
*10: The computer and PLC used to install the app must be provided by the customer. The computer and PLC, as well as the PLC and fuel cell unit, must be connected via LAN (hub relay).
*11 : On the side of the front face of the main unit, 400 mm space is required to open the door.
*12 : In case of attaching a design panel, 70 mm space is required for left and right sides.
Contact: panasonic_fuel_cell@gg.jp.panasonic.com
H2 Plant The content in this website is accurate at the time of publication but may be subject to change without notice. Please note therefore that these documents may not always contain the most up-to-date information. Please note that German, French and Chinese versions are machine translations, so the quality and accuracy may vary.