Forged pistons have been made in the same way for decades, with differences in machining differentiating one supplier’s product from another. But now, a new development called Aligned Grain Flow Technology (AFT) provides a breakthrough for additional strength without additional mass.
After several years of experimentation and development by JE Pistons’ Advanced Product Development group, AFT has been launched into the market. rotary eccentric shaft
AFT is about making the best use of the grains of metal within the piston. A forged piston is already stronger than a cast one. The cast piston has larger grains that are more three-dimensional in shape, but the source material for the forged piston – a long aluminum extrusion that’s cut off into piston-size slices – means those grains have already been worked into a longer, thinner form, which helps to prevent crack propagation.
The idea was to make even better use of the inherent advantages of forging and optimize crack resistance in highly stressed areas, such as where the pin tower meets the crown.
“There were additional manufacturing steps that we had to take to ensure that the grain structure was in the proper locations,” says Cody Mayer, JE’s senior manager of advanced product development. “We further work those grains to stretch them and form them around the contours of the piston forging shape. Longer, thinner grains that are compressed more tightly together, create additional grain boundaries in the most critical areas.”
In a piston, the grain boundaries in the metal provide resistance to cracks. Think of it as chopping a log: it’s much harder to cut across the grain, with each wood-cell fiber providing resistance to the axe. But if you slit the log from the top, it’ll crack much more easily along the grain.
“When a crack propagates through the material, it rarely happens all at once, especially in a fatigue situation in a reciprocating engine part that’s experiencing millions of load cycles,” says Mayer. “The crack starts very small and grows over thousands of cycles. But the elongated grains, packed tightly together, form walls to prevent the crack from progressing. The crack stops every time it hits a grain boundary. It’s much more difficult for it to propagate far enough through the piece to cause a failure.”
By placing the grain boundaries at the most highly stressed points on the piston, fatigue cracks can be resisted much more successfully.
“We’ve focused on the crown of the piston, in particular where the pin tower meets the crown,” he says. “We’ve wrapped grains around that joint and extended them across the face of the crown to resist the bending that combustion would normally induce. We’ve also applied them to the skirt.”
A similar principle is already used in the manufacturing of connecting rods. A rod’s elongated shape lends itself more easily to exploiting the grain advantages of the source extrusion. It was no easy task to do the same thing for a piston, however. To begin with, RWB’s engineers could use software to simulate the grain flow during the forging process. Subsequently, physical test samples were sectioned and etched to check the grain alignment after each change to the process.
An in-house forging facility enabled the development team to quickly test the impact of new processes. New tooling was also required, but this too could be made in-house, which further reduced the development time and ensured that every option could be explored on the road to the best result.
“If we had been working with an outside supplier, then we probably would have not had the ability to fine-tune the process in the way that we did,” Mayer says.
That final process will remain a trade secret, with a patent pending for Aligned Grain Flow Technology itself – the way in which it orients the grains and structures them for increased strength.
While AFT has already made its market debut in Ultra Series pistons, the technology lends itself to many applications. “AFT makes the piston stronger,” Mayer concludes. “We could have gone in two directions with that. We’ve chosen to start with Ultra Series pistons that are of equal weight but stronger, for high-power, high-boost applications. The technology would apply equally well to taking weight out of a conventional forged piston, while maintaining equal strength.”
This article was sponsored by JE Pistons. For more information, please visit our website at www.jepistons.com
We all recognize that internal combustion engines generate heat as a by-product of combustion. Both air-cooled and water-cooled engines deploy strategies to dissipate that heat. This is all done in an effort to keep the engine from running too hot. But what does that have to do with piston rings? Before we get to that,
We all recognize that internal combustion engines generate heat as a by-product of combustion. Both air-cooled and water-cooled engines deploy strategies to dissipate that heat. This is all done in an effort to keep the engine from running too hot.
But what does that have to do with piston rings? Before we get to that, we need to talk about another source of heat in an engine - friction.
Polymer coatings in the engine performance industry have become extremely popular in the past 5 years. The usage of polymer coatings has been widespread, not only in engine bearings, but also in pistons, cylinder heads, bolts, and other engine parts operating in heated and pressured environments. King Engine Bearings has been at the forefront of
The GT35 turbo, which is a universal application turbo, is fit for any four or six-cylinder engine, as well as 3.0L-6.0L engines.
MaXpeedingRods, a manufacturer of performance parts such as connecting rods, crankshafts, turbochargers, and coilovers, has announced sponsorship of British Drift Championship racers Oliver Evans and Duane McKeever. The performance parts company, established in 2006, reaches more than 4 million car enthusiasts across America, Australia, Asia, Europe and other countries. Oliver Evans, who hails from the
Cleaning is being done every day and is an integral part of many businesses and their processes. One of the most commonly asked questions about using sodium bicarbonate (a.k.a. baking soda) as a blasting abrasive is simply: How does it work? Let’s start with: What is abrasive blasting? Abrasive blasting uses either pressurized air or
Piston crown coating is a surprisingly affordable way to increase engine efficiency, horsepower and durability. It’s often said the internal combustion engines, which hold a special love/hate place in our heart, are basically air pumps, and while that’s a useful mental model when considering many aspects of how they operate, it’s more accurate to say
It’s been more than 100 years since the idea for a turbocharged engine was developed. Originally their use had been limited to very large diesel engines and while there have been additional innovations for use in automobiles, it was not always the most popular power adder. The boost was powerful but the cost was too
Sleeving an engine block is done for two primary reasons. The first is to repair a cracked or otherwise damaged cylinder to save the block. The second is increasing displacement by allowing for a larger bore size. In either case, the sleeving process must be performed carefully to ensure satisfactory results. Careful measurements are required
turbo shaft engine Content for engine professionals and enthusiasts