On October 29, 2024, a group of three U.S. manufacturers filed antidumping (AD) and countervailing duty (CVD) petitions on overhead door counterbalance torsion springs from China and India. The petitioners are IDC Group, Inc., Iowa Spring Manufacturing, Inc., and Service Spring Corp (collectively “Petitioners”).
The U.S. AD law imposes special tariffs to counteract imports that are sold in the United States at less than “normal value.” The U.S. CVD law imposes special tariffs to counteract imports that are sold in the United States with the benefit of foreign government subsidies. For AD/CVD duties to be imposed, the U.S. government must determine not only that dumping and/or subsidization is occurring, but also that there is “material injury” (or threat thereof) by reason of the dumped and subsidized imports. Importers are liable for any potential AD/CVD duties imposed. In addition, these investigations could impact purchasers by increasing prices and/or decreasing supply of overhead door counterbalance torsion springs. Stainless Steel Compression Springs
Please note that this section was not written by our authors but is taken verbatim from the petition.
The merchandise covered by these investigations is helically-wound, overhead door counterbalance torsion steel springs (“overhead door counterbalance torsion springs”). Overhead door counterbalance torsion springs are helical steel springs with tightly wound coils that store and release mechanical energy by winding and unwinding along the spring's axis by an angle, using torque to create a lifting force in the counterbalance assembly typically used to raise and lower overhead doors, including garage doors, industrial rolling doors, warehouse doors, trailer doors, and other overhead doors, gates, grates, or similar devices. The merchandise covered by these investigations covers all overhead door counterbalance torsion springs with a coil inside diameter of 15.8 millimeters (“mm”) or more but not exceeding 304.8 mm (measured across the diameter from inner edge to inner edge); a wire diameter of 2.5 mm to 20.4 mm; a length of 127 mm or more; and regardless of the following characteristics:
For purposes of the diameters referenced above, where the nominal and actual measurements vary, a product is within the scope if application of either the nominal or actual measurement would place it within the scope based on the definitions set forth above.
The steel torsion springs included in the scope of these investigations are produced from steel in which: (1) iron predominates, by weight, over each of the other contained elements; and (2) the carbon content is 2 percent or less, by weight.
Subject merchandise includes cones or other fittings attached to or entered with the subject overhead door counterbalance torsion springs. Subject merchandise also includes all subject overhead door counterbalance torsion springs entered as a part of overhead door kits, overhead door mounting or assembly kits, or as a part of a spring-operated motor assembly or as a part of a spring winder assembly kit for torsion springs. When counterbalance torsion springs are entered as a part of such kits, only the counterbalance spring and cones attached to or entered with the spring are within scope.
Subject merchandise also includes overhead door counterbalance torsion springs that have been further processed in a third country, including but not limited to cutting to length, attachment of hardware, cones or end-fittings, inclusion in garage door kits or garage door mounting or assembly kits, or any other processing that would remove the merchandise from the scope of these orders if performed in the country of manufacture of the in-scope overhead door counterbalance torsion springs.
All products that meet the written physical description are within the scope of these investigations unless specifically excluded. The following products are specifically excluded from the scope of these investigations:
The products subject to these investigations are currently classified under Harmonized Tariff Schedule of the United States (HTSUS) subheadings 7320.20.5020, 7320.20.5045 and 7320.20.5060. They may also be classified under HTSUS subheading 8412.90.9085 if entered as parts of spring-operated motors. They may also be classified in HTSUS subheading 8412.80.1000 (spring-operated motors) if entered as part of a spring counterweight assembly for an overhead door. They may also be classified in HTSUS subheading 7308.90.9590, a basket category that includes metal garage doors entered with mounting accessories or assemblies. Although the HTSUS subheadings are provided for convenience and Customs purposes, the written description of the scope of these investigations is dispositive.
The Petitioners allege the following dumping margins exist:
The following is an estimated schedule of investigations by the U.S. Department of Commerce (DOC) and the U.S. International Trade Commission (ITC):
DISCLAIMER: Because of the generality of this update, the information provided herein may not be applicable in all situations and should not be acted upon without specific legal advice based on particular situations. Attorney Advertising.
© Faegre Drinker Biddle & Reath LLP
Professional Spring Manufacturers Produce Various Types Of Stainless Steel Small Helical Torsion Springs Copyright © JD Supra, LLC