Cleaning, rather than replacing, a MAF sensor is quick and easy and can save you $300.
Over my 50-year career in the auto repair industry, I replaced thousands of defective, contaminated, shorted or simply-worn out mass air flow sensors (MAF). Mercesds-Benz Headlamp Level Sensor
![How to Clean A Mass Air Flow Sensor | Family Handyman](https://img7.grofrom.com/www.hchsensor.com/66fee18da4e17ba1c287aa1bc11d31ea.jpg)
After leaving the industry to become a vocational educator, I spent one summer at a Ford electronics facility as part of an "Educator in the Workplace" internship. As an auto technician, it was fascinating to see how car parts are designed, manufactured and tested.
One department I visited tested empty MAF sensor housings before electronic components were installed. Sophisticated measuring devices ensured the housings were the correct size to 1,000th of an inch and there was no slag on any seams. All for an empty shell that cost less than a dollar!
Once all the electronics were installed, the MAF sensor went through another series of tests. That's because MAFs are one of the most critical sensors needed to make our vehicles run and perform efficiently and run smoothly.
According to auto repair expert Bernie Johnson, "Today, MAF sensors are one of the most reliable parts on our cars and trucks." However, they do get dirty, and that's where MAF sensor cleaners come in. Here's what you need to know.
Bernie Johnson has almost 50 years of experience in the auto repair industry as an Automotive Service Excellence (ASE), Oldsmobile and Hyundai master technician. He is also a state certified emissions and safety inspection inspector at Faulkner Hyundai in Philadelphia, Pennsylvania.
Make sure the engine and sensor are cool, and the engine is off. Wear personal protection equipment. Read and follow all label safety instructions and directions when using spray MAF sensor cleaners, which are highly flammable. Work outdoors in a well-ventilated area.
A device that monitors the temperature and weight of air entering your engine. Your onboard computer (engine control module, aka ECM) needs that information to calculate the right amount of fuel for the engine to run properly under all operating conditions.
It heats a small, hot, delicate platinum wire or plate, then measures the current required to keep it at a constant temperature while air blows past it. The MAF sensor sends that information to the ECM, which then determines how much fuel to inject into the combustion chamber.
Over time, dust, debris and oil particles stick and bake onto the hot wire/plate. Eventually, those particles insulate the wire/plate from the air stream. This causes drivability problems, makes the Check Engine Light (CEL) illuminate, and increases tailpipe emissions.
Hard starting, stalling, rough idling, poor acceleration, black smoke from the exhaust, as well as poor gas mileage. A rotted-out or rusted MAF sensor hot wire/plate can keep your car from starting and needs to be replaced.
It depends. In my area (outside of Philadelphia, Pennsylvania) it runs from $300 to $375 — about $100 for labor and $275 for parts. (According to AAA, national labor rates range between $47 and $215 an hour.) This doesn't include diagnostic or other fees.
Bob Lacivita for Family Handyman
Take your time removing the sensor. Parts are plastic. They become brittle over time and can break.
Pro tip: Check and clean the air filter box of dust and debris and replace the air cleaner whenever cleaning the MAF sensor.
Using a MAF sensor cleaner:
Pro tip: Never use brake cleaner or any other type of cleaner on the MAF sensor. They can leave unwanted residue, ruining the sensor. Only use cleaners specifically for MAF sensors.
Bob Lacivita for Family Handyman
Ivan Las Heras/Getty Images
We are no longer supporting IE (Internet Explorer) as we strive to provide site experiences for browsers that support new web standards and security practices.
![How to Clean A Mass Air Flow Sensor | Family Handyman](https://img7.grofrom.com/www.hchsensor.com/b06b9980e12aeca6a7bdaa4b3a274d43.png)
VW HID Level Sensor We recommend our users to update the browser.