Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.
Scientific Reports volume 8, Article number: 793 (2018 ) Cite this article Cas 349 46 2
The highly efficient removal of uranium from mine tailings effluent, radioactive wastewater and enrichment from seawater is of great significance for the development of nuclear industry. In this work, we prepared an efficient U(VI) adsorbent by EDTA modified sugarcane bagasse (MESB) with a simple process. The prepared adsorbent preserves high adsorptive capacity for UO22+ (pH 3.0) and uranyl complexes, such as UO2(OH)+, (UO2)2(OH)22+ and (UO2)3(OH)5+ (pH 4.0 and pH 5.0) and good repeatability in acidic environment. The maximum adsorption capacity for U(VI) at pH 3.0, 4.0 and 5.0 is 578.0, 925.9 and 1394.1 mg/g and the adsorption capacity loss is only 7% after five cycles. With the pH from 3.0 to 5.0, the inhibitive effects of Na+ and K+ decreased but increased of Mg2+ and Ca2+. MESB also exhibits good adsorption for [UO2(CO3)3]4− at pH 8.3 from 10 mg/L to 3.3 μg/L. Moreover, MESB could effectively extract U(VI) from simulated seawater in the presence of other metals ions. This work provided a general and efficient uranyl enriched material for nuclear industry.
Uranium is a vital commodity for nuclear energy, using as fuel for electricity generation. However, mine tailings effluent and wastewater from nuclear industry are seriously harmful for ecological and human health due to its radiochemical and toxicological1,2. Moreover, extraction of uranium from unconventional resource such as seawater, which is nearly 1000 times higher than that available in terrestrial ores3,4, has received recent attention. Hence, the highly efficient enrichment of uranium from mine tailings effluent, radioactive wastewater and seawater is of great significance for the development of nuclear industry. Among all kinds of extraction methods, such as adsorption1,5,6,7, ion exchange8,9,10, chemical reduction11,12, biological processes13,14 and membrane processes15,16,17, adsorption has been widely employed to enrich uranyl form aqueous due to its low cost, simple design, and ease of operation. Recently, various kinds of organic adsorbents (such as such as amidoxime18,19,20, amine21,22,23, carboxylates24,25,26 functionalized adsorbents) and inorganic adsorbents (such as mesoporous Mg(OH)227,28,29, zero-valent iron30,31 and other functionalized inorganic adsorbents32,33) have been developed.
However, few adsorbent could be applied in all of mine tailings effluent, radioactive wastewater and seawater. The extraction is limited by some reasons: (1) aqueous uranium species is various, such as cationic UO22+, UO2OH+ and (UO2)2(OH)2+ in mine tailings effluent and radioactive wastewater34,35 and anionic [UO2(CO3)3]4− in seawater36,37, (2) the concentration of uranium is in a wide range concentrations (mg/L-μg/L), (3) there are large amount of competing metal ions, such as sodium, potassium, magnesium and calcium, and (4) adsorbent should have a great chemical and structural stability in both acidic (mine tailings effluent and radioactive wastewater) and alkaline (seawater) environment. Therefore, an adsorbent with remarkable adsorption properties and stability is necessary.
Agricultural waste materials are of particular interest since they are produced in great amounts and available worldwide38,39,40,41,42,43. These materials represent an interesting and attractive alternative as biosorbents because of their physico-chemical characteristic, particular structure, chemical stability, and high reactivity resulting from the presence of abundance functional groups on the surface. Moreover, it is well known that agricultural waste materials are renewable and biodegradable. In the application of adsorption, the excellent performance of different agricultural waste materials has been demonstrated, such as crop straws44, sawdust45,46,47, rice bran48,49, corncobs50,51, etc, which all have been widely studied for removing heavy metals from aqueous solution. Sugarcane bagasse (SB), a complex material containing cellulose, hemicellulose and lignin as major constituents, with high stability, abundant hydroxyl groups and low cost, has proven to be good candidate for supporting other functional compounds52,53. Recently, many efforts have been devoted to the preparation of SB-based composites for their applications in metal ion removal. For example, Yu et al. investigated the separation of Cu2+ and Pb2+ by tetraethylenepentamine modified SB54; Ramos et al. grafted phthalate on SB for the uptake of Co2+, Cu2+, and Ni2+ 55; Palin et al. evaluated the biosorption of Pb2+ utilizing SB colonized by Basidiomycetes56. Therefore, it would be attractive to introduce SB as the substrate to fabricate adsorbent for uranium extraction.
EDTA is a kind of biodegradable chelating agent which could form stable (1:1) complexes with rare earth ions in aqueous solution57,58. In this study, EDTA was introduced to SB through esterification for adsorption U(VI) from aqueous solutions and the composites (MESB) could be easily recycled by magnetic separation avoiding secondary pollution and loss by magnetic functionalization. This work aimed to investigate whether the adsorbent could efficiently extract uranium from mine tailings effluent, radioactive wastewater and seawater, including: (1) test the adsorption properties for uranium from acidic (pH = 3.0, 4.0 and 5.0) and alkaline (pH = 8.3) conditions, (2) evaluate the stability by regeneration efficiency and reusability, (3) determine the effects of co-existing cations ions (K+, Na+ Mg2+ and Ca2+) and (4) examined the adsorption for low-concentration U(VI) (μg/L) with a vast amount of other metals ions. This work provides both fundamental knowledge and practical aspects that are valuable for interpreting adsorption of uranium on MESB and for effective enrichment of uranium from mine tailings effluent, radioactive wastewater and seawater.
The morphology and structure of SB and MESB before and after the adsorption of U(VI) were characterized by SEM and TEM measurements. As shown in Fig. 1Aa, MESB is present as wrinkled and sheet-like structure. The SEM image for SB is shown in Fig. 1Ab. It can be seen that the pristine SB shows a sheet-like structure with smooth surface and tiny wrinkles. After co-precipitation to form MSB composite, Fe3O4 NPs are decorated on the surface of SB. TEM image (Figure S1) clearly shows that SB are the matrix of the Fe3O4 NPs, and the average size of the Fe3O4 NPs is about 10 nm. As shown in Fig. 1Ac, the magnetic NPs are not broken and maintained regular shapes, during the introduction of EDTA. After the adsorption of U(VI), the sheet-like structure of SB and MESB is retained (Figure S2A and B). Figure S2C shows U(VI) exist on the surface of SB in the form of small particles. Because only hydroxyl groups of SB could interact with U(VI), a small amount of uranium is adsorbed. However, the coverage of U(VI) on the surface of MESB increases significantly after modified by EDTA in Figure S2D.
SEM of MESB (Aa) and TEM of SB (Ab) and MESB (Ac). FTIR spectra of SB and MESB (B). XRD pattern of MSB and MESB (C), and Magnetization curve of MSB and MESB.
Figure 1B gives the FT-IR spectra for SB and MSBE. As can be seen, the comparative FTIR spectra of both materials show intense band at 3400 cm−1 and 1051 cm−1 assigned to the vibrational modes of hydroxyl groups present in the polysaccharide fraction of SB. The absorption bands at 2902 cm−1 should be assigned to the stretching vibration of C-H. In the FT-IR spectrum of SB, the bands at 1636 and 1608 cm−1 are correspond to the stretching vibration of hemicellulose of C=O and the stretch vibration of C-O, respectively. Compared with the spectrum of SB, in the spectrum of MESB, the appearance of strong bands at 1749 cm−1 can be attributed to axial deformation of the ester bond, and the arising of strong bands at 1599 and 1396 cm−1 are correspond to the asymmetric and symmetric stretching of the carboxylate ion, respectively. The ester and acid IR bands indicate that EDTAD acylated the hydroxy group of SB to generate an ester bond with consequent release of a carboxylic acid functional group.
X-ray diffraction patterns of MSB and MSBE are shown in Fig. 1C. The intense peaks of MSB at 2θ values of 30.1°, 35.5°, 43.3°, 53.4°, 57.2°, and 62.5° indexed to (220) (311) (400) (422) (511) and (440), respectively, which are consistent with the standard XRD data, indicating that the Fe3O4 NPs were successfully coated on SB. The intense peaks slightly reduced after introducing EDTA.
The magnetic properties were investigated with a VSM. According to Fig. 1D, the VSM plot showed a value of 3.41 emu/g for the saturation magnetization of MSB and no hysteresis loop in the magnetization59. This magnetic susceptibility value is reasonable to believe that the simple and rapid separation of MSB can be achieved under a magnetic field. For MESB, a saturation magnetization of 2.82 emu/g was obtained, while decreased to 0.59 emu/g due to the shielding of EDTA coating resulting from the modification process. However, the MESB with declined saturation magnetization value also possesses enough magnetic response to meet the need of magnetic separation, which would bring a great convenience in the practical applications of the adsorbent (the inset of Fig. 1D).
Table 1 shows the elemental analysis results of SB, MSB and MSBE. It can be seen that the nitrogen content decreased drastically when MSB was obtained. This may be attributed to the decomposition of N-containing organic of SB under basic conditions. While, the nitrogen contents were increased from 0.40 to 1.55 after esterification. The obvious increase of nitrogen content also can be observed from the decrease of mass ratio of carbon and nitrogen from 104.98 to 25.08, which could prove the introduction of the EDTA. Moreover, it was possible to determinate the concentration of EDTA moiety in the modified materials (CED TA (0.411 mmol/g)).
The complexation of heavy metal ions by a chelating ligand strongly depends on pH, because the pH of the adsorption medium affect the presence form of metal ions greatly and also have a strongly influence on the adsorbents especially the ones containing functional groups60,61. U(VI) from mine tailings effluent and radioactive wastewater common exists in acid conditions, which limited adsorption to sorbents for positively charged and electrostatically repel the positive uranyl species. Moreover, most of the adsorbents are difficult to be stable under acidic conditions and the environment will be caused secondary pollution. As shown in Fig. 2, the effect of pH on the adsorption capacity of U(VI) by SB, MSB and MESB was evaluated in a pH range of 2.0–5.0. It is clear that MESB is more helpful to adsorb U(VI) in acid conditions than SB and MSB. The pHzpc (pH zero point charge, Figure S3) of MESB is found to be 4.0. When pH < 4.0, carboxyl groups are completely protonated. Although repulsive electrostatic interactions with H+, the adsorption rate of positively charged uranyl ion is still maintained above 50%. As the pH values increased from 4.0 to 5.0, the surface charge of MESB is negative, which is prone to adsorb positively charged metal ions on their surfaces and the adsorption rate reaches 86.3% and 98.3% (the inset of Fig. 2).
Effect of pH on U(VI) adsorption on MESB and and adsorption rate (insert). (C0 = 100 mg/L, V = 50 mL, T = 298 K, m = 0.02 g, t = 60 min).
Figure 3A shows the equilibrium adsorption capacity of U(VI) on MESB as a function of different initial uranium concentrations at pH 3.0, 4.0 and 5.0. The adsorption capacity increases rapidly with the initial concentration increasing until equilibrium and the equilibrium adsorption capacity at pH 3.0, 4.0 and 5.0 are 530.15, 981.25 mg/g and 1358.75, respectively.
Effect of initial concentration of MESB (A) and corresponding Langmuir adsorption isotherms (B) at pH 3.0, 4.0 and 5.0 (A). (V = 50 mL, T = 298 K, m = 0.02 g, t = 60 min) Effect of contact time of MESB (C) and their corresponding pseudo second-order kinetics (D). (C0 = 100 mg/L, V = 50 mL, T = 298 K, m = 0.02 g).
The adsorption isotherms reveal the interactive behaviors between the adsorbent and adsorbate, which have been simulated by utilizing the well-established fundamental models. Langmuir and Freundlich isotherm models expressed in Eqs. (1) and (2), respectively, are used to understand the adsorption mechanism in this paper.
where Ce is the concentration of the adsorbate in solution at equilibrium (mg/L), Qe is the amount of U(VI) adsorbed at equilibrium (mg/L), and Qmax represents the saturated monolayer adsorption capacity (mg/g) of Langmuir isotherm model62. KL is the Langmuir adsorption constant related to the energy of adsorption (L/mg). KF is the Freundlich constant related to the adsorption capacity [(mg/g) (L/mg)1/n] and n is the Freundlich exponent related to adsorption intensity. The Freundlich model is suitable for the nonideal adsorption on the heterogeneous surfaces as well as multilayer adsorption63.
Langmuir and Freundlich isotherm parameters calculated from fitting processes are listed in Table S1 and shown in Fig. 3B. It can be seen that the Langmuir equation fits the experimental data better than the Freundlich model with a higher correlation coefficient (R2) at pH 3.0, 4.0 and 5.0, implying that the adsorption process results in the formation of a monolayer coverage of various uranium species on MESB. The maximum adsorption capacity of MESB was evaluated as 578.0, 925.9 and 1394.1 mg/g at pH 3.0, 4.0 and 5.0, respectively. Previous studies have demonstrated that the major component of uranium is UO22+ at pH 3.0, and then become complicated, such as UO2(OH)+, (UO2)2(OH)22+ and (UO2)3(OH)5+ with pH increased to 5.064. The results demonstrate that MESB is favorable for the adsorption of various uranium species, which is probably due to the strong chelating ability of EDTA.
Furthermore, the essential characteristics of the Langmuir isotherm can be described by a separation factor, RL65, which is defined as follows:
where KL is the Langmuir equilibrium constant and C0 is the initial concentration of metal ion. The value of RL provides guidance for the possibility of the adsorption process to proceed. RL > 1.0, unsuitable; RL = 1.0, linear; 0 < RL < 1.0, suitable; RL = 0, irreversible. The values of RL, were found to range from 0.4200 to 0.0569, 0.2606 to 0.0285 and 0.1492 to 0.0144 at pH 3.0, 4.0 and 5.0, respectively, indicating the suitability of MESB as adsorbents for the adsorption of U(VI) ions at acid conditions (Figure S4).
Another factor can help understanding the behavior of the adsorption of U(VI) ions on MESB, is the Langmuir surface coverage rate (θ), which relates the surface coverage of the fiber to the initial concentration of U(VI) ions66 and can be calculated using the following equation:
The relationship of θ and initial concentration of U(VI) ions was depicted in Figure S5. Evidently, the adsorption of U(VI) ions on MESB in the early age was very fast (low coverage of fiber surface and plenty of free active sites are available for binding with the metal ions) then tends to be a plateau at higher surface coverage where most of the active sites are occupied. This implies the applicability of Langmuir model to describe the adsorption of U(VI) ions on MESB.
The effect of contact time was investigated in a kinetics study of the adsorption process. Figure 3C shows the time profile of U(VI) adsorption at pH 3.0, 4.0 and 5.0 in terms of adsorption capacity. It is observed that adsorption generally achieved the equilibrium within 60 min. The results indicate that higher pH not only has higher adsorption rate but also higher adsorption efficiency.
The following pseudo-first-order67 and pseudo-second-order68 models are employed to further interpret the kinetic data:
where qe and qt (mg/g) are the adsorption capacities at equilibrium and at time t (min), respectively; k1 and k2 are the rate constant of the pseudo-first-order and pseudo-second-order model. The corresponding kinetic parameters from both models are listed in Table S2. Higher correlation coefficient (R2 > 0.99 for both) as well as value of qe,cal (276.2, 438.6,and 490.2 mg/g) at pH 3.0, 4.0 and 5.0, approximating to qe,exp (273.7, 433.7, and 490.1 mg/g), indicates that pseudo-second-order model describes the adsorption process better (Fig. 3D). This model is based on the assumption that the rate-limiting step of the reaction is due to chemical adsorption69.
In order to investigate if pore or film diffusion was the controlling step in the adsorption, intra-particle diffusion model was further tested as follows70:
Figure S6 shows the intra-particle diffusion plots for the U(VI) adsorption on MESB at pH 3.0, 4.0 and 5.0. It is apparent that two linear portion appear in all of the plots, which indicates that the adsorption is affected by two steps. This could be explained as follows: the first portion represents instantaneous adsorption or external surface adsorption stage, in which large numbers of U(VI) are adsorbed rapidly by COO- of MESB. After almost all the exterior COO- is occupied, the second portion of the plots is nearly parallel, suggesting that equilibrium state reached at last. The intra-particle diffusion rate constants in every step follow the order of kpH5 > kpH4 > kpH3, which are presented in Table S2. At low pH abundant of hydronium ion (H3O+) could compete with U(VI) for binding on the functional groups (binding sites). Moreover, when pH < 4.0 the surface charge of MESB is positive, which is difficult to adsorb positively charged metal ions on its surfaces. All of these could affect the adsorption of U(VI). Therefore, the adsorption has a shorter equilibrium time at pH 5.0 than 4.0 and 3.0.
Table S3 shows effects of coexisting K+ on U(VI) adsorption by MESB at pH = 3.0, 4.0 and 5.0. It was observed that the adsorption of U(VI) decreased with the increase of K+ concentration at any pH (Fig. 4A). However, as the pH increased from 3.0 to 5.0, the inhibitive effects decreased. The effect of Na+ on the adsorption of U(VI) is the same as that of K+ (Fig. 4B). K+ and Na+ cannot coordinate with EDTA but can be adsorbed onto the surface of MESB by electrostatic interactions. At low pH, a large number of H+ concentrated on negatively charged surface of MESB and then the surface turns positive resulting in repulsion for cations. Na+ and K+ are easier to aggregate onto surface of adsorbents due to their smaller ionic radius than uranium (0.102, 0.138 and 0.604–0.684 nm for Na+, K+ and UO22+)71, which make adsorbents more positive leading to decrease of adsorption towards uranyl. Therefore, effect on the adsorption of uranium is stronger with the increase in concentration of Na+ and K+. With the increase of pH, the electrostatic repulsion of adsorbent and ion decreases gradually with decrease in contents of H+ in solutions, which makes the coordination between adsorbents and uranyl strengthened so as to increase the adsorption rate. In Fig. 4C and D, the adsorption rate of uranium decreases with the increasing concentration of Mg2+ and Ca2+ the same as that of Na+ and K+. However, with the increase of pH, the effect of coexisting Mg2+ and Ca2+ was opposite with Na+ and K+. Based on previous studies, EDTA can be coordinated with Mg2+ and Ca2+ and higher pH (acidic condition) is favor for coordination. As a result, high concentration of Mg2+ and Ca2+ and high pH (pH = 5) will have a greater impact on the adsorption of uranium. Overall, the inhibitive effects of coexisting ions follow the order of: Ca2+ > Mg2+ > Na+ > K+ and affected by pH.
Effect of coexisting ions on U(VI) adsorption on MESB at pH 3.0, 4.0 and 5.0. (C0 = 100 mg/L, V = 50 mL, T = 298 K, m = 0.02 g, t = 60 min).
The reusability and stability of MESB are of great importance for practical application. According to the previous result, MESB have poor U(VI) adsorption ability when pH < 2. HNO3 (0.05–0.4 mol/L) is chosen to evaluate the reutilization performance. The results obtained are given in Fig. 5A. The elution efficiency is above 99% when the acid concentration is greater than 0.3 mol/L, suggesting that HNO3 is an effective eluent for the recovery of the adsorbent. And 99% of U(VI) will be desorbed within an hour (the inset of Fig. 5A). Therefore, reusability experiments are subsequently estimated using 0.3 mol/L HNO3 as the desorbing agent and the results are shown Fig. 5B. It is observed that regenerated MESB still has high adsorption capacity even after 5 cycles of adsorption/desorption, indicating that MESB is a stable and recyclable adsorbent. After desorption, the eluent is first adjusted to neutral and then add NH4OH to get (NH4)2U2O7 precipitate, which can be further reduced to UO2 by H2:
Desorption rate of MESB at different concentrations of HNO3 (A) and effect of time on U(VI) desorption (insert). Recycling of the MESB in the adsorption of U(VI) (B).
Therefore, the acceptable adsorption ability and regeneration ability proved that MESB has a potential application prospect for the preconcentration of U(VI) from acidic conditions.
Although estimated 4.5 billion tons of uranium dissolved in seawater which is much larger than the terrestrial sources, the concentration of uranium is extremely low at ∼ 3.3 μg/L and is found to be present principally as the anionic triscarbonatouranato (VI) [UO2(CO3)3]4− species. Moreover, basic pH (~8.3), and myriad of other metals present also contribute to the challenge of oceanic extractions.
In order to determine the adsorption property of [UO2(CO3)3]4− on MESB, the adsorption process was carried on 10 mg/L of [UO2(CO3)3]4− at pH 8.3. According to Figure S7, most uptake of U(VI) occurred in the first 60 min, and full adsorption equilibrium was reached within 120 min. At equilibrium, the U(VI) adsorption capacities was 100 mg/g with an adsorption efficiency of 73.2%. The result indicates MESB also has excellent adsorption ability for [UO2(CO3)3]4− at alkaline conditions. A higher correlation coefficient (R2) and a value of qe,cal (151.7 mg/g) that is close to qe,exp (150.2 mg/g) indicates that the adsorption process follows the pseudo-second-order model.
To further investigate whether MESB is suitable for the extraction of uranium from seawater, we examined the applicability of adsorbent in the extraction of simulated seawater with low concentration of U(VI) and a vast amount of other metals ions with similar or even higher concentrations (Table S4). As shown in Fig. 6, U(VI) is still effectively adsorbed onto MESB not only at initial concentration of 100 ppb but also at an extremely low concentration of 3.3 ppb. These results suggest that MESB is a promising uranium adsorbent even for seawater where the basic pH, low concentration and competition of coexisting cations to U(VI) is overwhelming.
The adsorption rate of U\(VI) by MESB in simulated seawater. (V = 50 mL, T = 298 K, m = 0.02 g, t = 12 h).
We have reported here a general and efficient uranyl enriched material, EDTA modified sugarcane bagasse, for nuclear industry. The prepared adsorbent preserved good adsorption properties in both acidic (mine tailings effluent and radioactive wastewater) and alkaline (seawater) environment. Under acid conditions, MESB was favorable for the adsorption of UO22+ (pH 3.0) and uranyl complexes, such as UO2(OH)+, (UO2)2(OH)22+ and (UO2)3(OH)5+ (pH 4.0 and pH 5.0) and the adsorption capacity was 578.0, 925.9 and 1394.1 mg/g at pH 3.0, pH 4.0 and pH 5.0, respectively. The coexisting of Na+, K+, Mg2+ and Ca2+ could decrease the adsorption capacity and affected by pH. With the pH from 3.0 to 5.0, the inhibitive effected of Na+ and K+ decreased but increased of Mg2+ and Ca2+. MESB also exhibited excellent chemical and structural stability in acid eluent and the adsorption capacity loss was only 7% after five cycles. Under alkaline conditions, MESB show strong coordination to [UO2(CO3)3]4− at pH 8.3. Moreover, MESB could effectively extract low concentration U(VI) (103.9–3.3 μg/L) from simulated seawater in the presence of other metals ions. This work provided a general and efficient uranyl enriched material for nuclear industry.
SB was repeatedly washed with deionized water to remove dirt and soluble impurities and then dried at 80 °C for 24 h. Subsequently, they were crushed and sieved to a particle size of under 150 (0.1 mm) meshes using a standard sieve. Ethylenediamine tetraacetic acid (EDTA) was purchased from Xiya (China). N,N-dimethylformamide (DMF) was purchased from Fuyu (China). Other reagents obtained from Kermel, China, were analytical grade. All the chemical reagents in this work were used without any further treatment.
Magnetic SB (MSB) was prepared by a coprecipitation method. In a 150 mL beaker, 0.417 g of ferrous chloride tetrahydrate (FeCl2·4H2O) and 0.405 g of ferric chloride hexahydrate (FeCl3·6H2O) were taken and dissolved by the addition of 45 mL water containing 3 g SB under ultrasound irradiation. Then, ammonium hydroxide (NH3·H2O) solution was added dropwise into the beaker until the pH reached 10. Black precipitates appeared immediately after adding ammonium hydroxide solution. During the reaction process, the temperature was maintained at 60 °C. The magnetic adsorbent was collected by magnetic separation after 1 h reaction and washed several times with water and ethanol. Finally, MSB was obtained after dried at 60 °C for 3 h.
EDTAD preparation method was described by Capretta et al.72. The prepared EDTAD (1.0 g) was added to 100 mL of N,N-dimethylformamide (DMF) containing 1.0 g of MSB in a three neck round bottom flask. After the mixture was stirred at 60 °C for 4 h, MESB was separated by an external magnet and washed with DMF, saturated sodium bicarbonate solution and deionized water successively. Then MESB was dried at 60 °C for 6 h and preserved in a desiccator.
MESB was characterized by several techniques. The morphology of the material were examined by scanning electron microscope (SEM, JSM-6480A), transmission electron microscopy (TEM, FEI Tecnai G2 S-Twin). X-ray diffraction (XRD) analysis was performed on a Rigaku D/max-IIIB diffractometer with Cu Kα irradiation (λ = 1.54178 Å) for determining the structure. The diffractgrams were recorded in the 2θ range 5°–90°. Qualitative chemical structure assessment was done by FT-IR analysis (PerkinElmer Spectrum 100) in a range of 4000–500 cm−1. A vibrating sample magnetometer (VSM, LakeShore 7304) was used to characterize the magnetic properties. The element content was measured by element analyzer (Vario Macro). The concentrations of metal ions were analyzed using inductively coupled plasma-atomic emission spectroscopy (ICP-AES, Optima-7000DV).
Individual stock solution of 1000 mg/L U(VI) was prepared by dissolving UO2(NO3)2·6H2O in deionized water. Adsorption experiments were performed in a 50 mL U(VI) solution with initial concentrations of 50, 100, 150, 200, 300, 400, 500, or 600 mg/L, 10 mg adsorbent and the solution pH adjusted to 3.0, 4.0 and 5.0 with HNO3 or NaOH. The effect of solution pH was evaluated in the case of 100 mg/L U(VI), 10 mg adsorbent and where the contact time was 60 min. For kinetics studies, the solution was shaken at 200 rpm for 5, 10, 15, 20, 30, 40, 60 or 80 min. Uranyl carbonate was prepared following the methodology described by Sapretta et al.73 and adjusted pH to 8.3.
The effect of coexisting ions for uranium (VI) adsorption onto MESB was tested through a 1-h adsorption process at 298 K. The solution used in this experiment contained four common monovalent and bivalent cations-Na+, K+, Mg2+ and Ca2+, with the concentration 1~5 times than uranium (VI) (mole ratio). An enhanced simulated seawater test was performed following our previous work74. MESB was added into simulated seawater containing U(VI) with initial concentrations of 3, 10, 30, 50 or 100 μg/L, after shaking at 200 rpm for 120 min, the residual U(VI) ions in solution was analysed by ICP-MS.
After adsorption experiments, MESB was washed thoroughly with deionized water until U(VI) ion was not detected in the rinsing solution and then dried in a vacuum oven at room temperature. 50 mL of 0.05–0.4 mol/L HNO3 solution was mixed with the dried MESB for desorption. After the mixture was shaken for 5, 10, 30, 60, 120 or 180 min, the concentrations of U(VI) in the solution were analyzed. The experiment was repeated five times in order to evaluate the recyclability of MESB.
Wang, Z. et al. Visualization ofAdsorption: Luminescent Mesoporous Silica-Carbon Dots Composite for Rapid and Selective Removal of U(VI) and in Situ Monitoring the Adsorption Behavior. Acs Appl Mater Inter 9, 7392–7398 (2017).
Keranen, A. et al. Quaternized pine sawdust in the treatment of mining wastewater. Environ Technol 37, 1390–1397 (2016).
Article CAS PubMed Google Scholar
Barbano, P. G. & Rigali, L. Spectrophotometric Determination of uranium in sea water after extraction with aliquot-336. Anal Chim Acta 96, 199–201 (1978).
Report of the Working Party on Extraction of uranium from seawater; United Kingdom Atomic Energy Authority, October (1976).
Manos, M. J. & Kanatzidis, M. G. Layered Metal Sulfides Capture Uranium from Seawater. J Am Chem Soc 134, 16441–16446 (2012).
Article CAS PubMed Google Scholar
Carboni, M., Abney, C. W., Liu, S. B. & Lin, W. B. Highly porous and stable metal-organic frameworks for uranium extraction. Chem Sci 4, 2396–2402 (2013).
Lu, Y. Uranium extraction coordination chemistry in the ocean. Nat Chem 6, 175–177 (2014).
Article CAS PubMed Google Scholar
Zhu, X. P. & Alexandratos, S. D. Development of a new ion-exchange/coordinating phosphate ligand for the sorption of U(VI) and trivalent ions from phosphoric acid solutions. Chem Eng Sci 127, 126–132 (2015).
Liu, W., Zhao, X., Wang, T., Zhao, D. Y. & Ni, J. R. Adsorption of U(VI) by multilayer titanate nanotubes: Effects of inorganic cations, carbonate and natural organic matter. Chem Eng J 286, 427–435 (2016).
Gu, B. H., Ku, Y. K. & Jardine, P. M. Sorption and binary exchange of nitrate, sulfate, and uranium on an anion-exchange resin. Environ Sci Technol 38, 3184–3188 (2004).
Article ADS CAS PubMed Google Scholar
Eglizaud, N., Miserque, F., Simoni, E., Schlegel, M. & Descostes, M. Uranium(VI) interaction with pyrite (FeS2): Chemical and spectroscopic studies. Radiochim Acta 94 (2006).
Hua, B. & Deng, B. L. Comment on “Reductive Immobilization of Uranium(VI) by Amorphous Iron Sulfide” Response. Environ Sci Technol 43, 1237–1238 (2009).
Article ADS CAS Google Scholar
Wang, T. S., Zheng, X. Y., Wang, X. Y., Lu, X. & Shen, Y. H. Different biosorption mechanisms of Uranium(VI) by live and heat-killed Saccharomyces cerevisiae under environmentally relevant conditions. J Environ Radioactiv 167, 92–99 (2017).
Li, D. X. et al. An experimental study on the inhibitory effect of high concentration bicarbonate on the reduction of U(VI) in groundwater by functionalized indigenous microbial communities. J Radioanal Nucl Ch 307, 1011–1019 (2016).
Villalobos-Rodriguez, R. et al. Iron influence on uranium removal from water using cellulose acetate membranes doped with activated carbon. Desalin Water Treat 56, 3476–3485 (2015).
Gao, M. W., Zhu, G. R., Wang, X. H., Wang, P. & Gao, C. J. Preparation of short channels SBA-15-PVC membrane and its adsorption properties for removal of uranium(VI). J Radioanal Nucl Ch 304, 675–682 (2015).
Kryvoruchko, A. P., Yu, L., Atamanenko, I. D. & Kornilovich, B. Y. Ultrafiltration removal of U(VI) from contaminated water. Desalination 162, 229–236 (2004).
Xiong, J. et al. Polypropylene Modified with Amidoxime/Carboxyl Groups in Separating Uranium(VI) from Thorium(IV) in Aqueous Solutions. Acs Sustain Chem Eng 5, 1924–1930 (2017).
Dai, Y. et al. Preparation of hollow SiO2 microspheres functionalized with amidoxime groups for highly efficient adsorption of U(VI) from aqueous solution. J Radioanal Nucl Ch 311, 2029–2037 (2017).
Ji, G. J. et al. Preparation of amidoxime functionalized SBA-15 with platelet shape and adsorption property of U(VI). Sep Purif Technol 174, 455–465 (2017).
Zhu, K. R. et al. Fabrication of hierarchical core-shell polydopamine@MgAl-LDHs composites for the efficient enrichment of radionuclides. Appl Surf Sci 396, 1726–1735 (2017).
Article ADS CAS Google Scholar
Zou, H. B., Zhou, L. M., Huang, Z. W., Liu, Z. R. & Luo, T. A. Characteristics of equilibrium and kinetic for U(VI) adsorption using novel diamine-functionalized hollow silica microspheres. J Radioanal Nucl Ch 311, 269–278 (2017).
Chen, M. M. et al. The extraction of uranium using graphene aerogel loading organic solution. Talanta 166, 284–291 (2017).
Article CAS PubMed Google Scholar
Xie, Y., Helvenston, E. M., Shilller-Nickles, L. C. & Powell, B. A. Surface Complexation Modeling of Eu(III) and U(VI) Interactions with Graphene Oxide. Environ Sci Technol 50, 1821–1827 (2016).
Article ADS CAS PubMed Google Scholar
Vivero-Escoto, J. L., Carboni, M., Abney, C. W., deKrafft, K. E. & Lin, W. B. Organo-functionalized mesoporous silicas for efficient uranium extraction. Micropor Mesopor Mat 180, 22–31 (2013).
Duan, G. J., Liu, T. H., Wu, W. S. & Yang, Y. Adsorption of UO22+ from aqueous solution onto copolymers of styrene and maleic anhydride. J Radioanal Nucl Ch 295, 2193–2201 (2013).
Li, L. X., Xu, D., Li, X. Q., Liu, W. C. & Jia, Y. Excellent fluoride removal properties of porous hollow MgO microspheres. New J Chem 38, 5445–5452 (2014).
Chen, Z. et al. Adsorption-Induced Crystallization of U-Rich Nanocrystals on Nano-Mg(OH)(2) and the Aqueous Uranyl Enrichment. Acs Appl Mater Inter 6, 1301–1305 (2014).
Zhuang, Z. Y. et al. Interfacial Engineering Improved the Selective Extraction of Uranyl from Saline Water by Nano-Mg(OH)(2) and the Underlying Mechanism. Acs Sustain Chem Eng 4 (2016).
Zhang, Z. B. et al. Comparison of U(VI) adsorption onto nanoscale zero-valent iron and red soil in the presence of U(VI)-CO3/Ca-U(VI)-CO3 complexes. J Hazard Mater 300, 633–642 (2015).
Article CAS PubMed Google Scholar
Crane, R. A., Pullin, H. & Scott, T. B. The influence of calcium, sodium and bicarbonate on the uptake of uranium onto nanoscale zero-valent iron particles. Chem Eng J 277, 252–259 (2015).
Zou, Y. D. et al. Glycerol-Modified Binary Layered Double Hydroxide Nanocomposites for Uranium Immobilization via Extended X-ray Absorption Fine Structure Technique and Density Functional Theory Calculation. Acs Sustain Chem Eng 5, 3583–3595 (2017).
Zou, Y. D. et al. Controllable Synthesis of Ca-Mg-Al Layered Double Hydroxides and Calcined Layered Double Oxides for the Efficient Removal of U(VI) from Wastewater Solutions. Acs Sustain Chem Eng 5 (2017).
de Carvalho, C. A. et al. Hydrochemical assessment of surface water in watersheds near the Uranium Mining and Milling Facilities of Caldas, Brazil. Environ Earth Sci 75 (2016).
Li, F. Z. et al. Microorganism-derived carbon microspheres for uranium removal from aqueous solution. Chem Eng J 284, 630–639 (2016).
Chatterjee, S. et al. Synthesis of Naphthalimidedioxime Ligand-Containing Fibers for Uranium Adsorption from Seawater. Ind Eng Chem Res 55, 4161–4169 (2016).
Chouyyok, W. et al. Nanostructured Metal Oxide Sorbents for the Collection and Recovery of Uranium from Seawater. Ind Eng Chem Res 55, 4195–4207 (2016).
Bahrami, A., Soltani, N., Pech-Canul, M. I. & Gutierrez, C. A. Development of metal-matrix composites from industrial/agricultural waste materials and their derivatives. Crit Rev Env Sci Tec 46, 143–207 (2016).
Yahya, M. A., Al-Qodah, Z. & Ngah, C. W. Z. Agricultural bio-waste materials as potential sustainable precursors used for activated carbon production: A review. Renew Sust Energ Rev 46, 218–235 (2015).
Sarma, P. J., Kumar, R. & Pakshirajan, K. Batch and Continuous Removal of Copper and Lead from Aqueous Solution using Cheaply Available Agricultural Waste Materials. Int J Environ Res 9, 635–648 (2015).
Pinkas, J. et al. Synthesis and Structure of Titanium(III) Bis(decamethyltitanocene) Oxide. Organometallics 32, 6306–6314 (2013).
Foo, L. P. Y., Tee, C. Z., Raimy, N. R., Hassell, D. G. & Lee, L. Y. Potential Malaysia agricultural waste materials for the biosorption of cadmium(II) from aqueous solution. Clean Technol Envir 14, 273–280 (2012).
Boumaza, S., Kaouah, F., Berrama, T., Trari, M. & Bendjama, Z. Optimization of preparation conditions for activated carbon from waste materials of agricultural origin for the removal of basic red 46. Chemometr Intell Lab 118, 311–316 (2012).
Tong, X. J., Li, J. Y., Yuan, J. H. & Xu, R. K. Adsorption of Cu(II) by biochars generated from three crop straws. Chem Eng J 172, 828–834 (2011).
Ertugay, N. Basic Violet 10 (BV10) removal from aqueous solutions using sawdust of Swietenia mahagoni (Mahogany trees): adsorbent characterization, adsorption isotherm, kinetics, and thermodynamic studies. Desalin Water Treat 57, 12335–12349 (2016).
Salazar-Rabago, J. J. & Leyva-Ramos, R. Novel biosorbent with high adsorption capacity prepared by chemical modification of white pine (Pinus durangensis) sawdust. Adsorption of Pb(II) from aqueous solutions. J Environ Manage 169, 303–312 (2016).
Article CAS PubMed Google Scholar
Komnitsas, K., Zaharaki, D., Bartzas, G., Kaliakatsou, G. & Kritikaki, A. Efficiency of pecan shells and sawdust biochar on Pb and Cu adsorption. Desalin Water Treat 57, 3237–3246 (2016).
Suratman, A., Kamalia, N. Z. & Kusumawati, W. A. Adsorption and desorption of Zn(II) and Cu(II) on Ca-alginate immobilized activated rice bran. Iop Conf Ser-Mat Sci 107 (2016).
Kanwal, F., Rehman, R., Anwar, J. & Saeed, M. Removal of Lead(II) from Water by Adsorption on Novel Composites of Polyaniline with Maize Bran, Wheat Bran and Rice Bran. Asian J Chem 25, 2399–2404 (2013).
Liu, D., Zhang, Z. P. & Ding, Y. G. A Simple Method to Prepare Magnetic Modified Corncobs and its Application for Congo Red Adsorption. J Disper Sci Technol 37, 73–79 (2016).
Nadeem, R. et al. Production of physically and chemically modified biomass of corncob and its applications for the removal of Co(II) ion from its aqueous solution: optimum conditions determination. Desalin Water Treat 71, 321–326 (2017).
Ferreira, B. C. S. et al. Application of a new carboxylate-functionalized sugarcane bagasse for adsorptive removal of crystal violet from aqueous solution: Kinetic, equilibrium and thermodynamic studies. Ind Crop Prod 65, 521–534 (2015).
Kadam, A. A., Kulkarni, A. N., Lade, H. S. & Govindwar, S. P. Exploiting the potential of plant growth promoting bacteria in decolorization of dye Disperse Red 73 adsorbed on milled sugarcane bagasse under solid state fermentation. Int Biodeter Biodegr 86, 364–371 (2014).
Yu, J., Xiong, W., Zhu, J. & Chi, R. Separation of Cu2+ and Pb2+ by tetraethylenepentamine-modified sugarcane bagasse fixed-bed column: selective adsorption and kinetics. Int J Environ Sci Te 13 (2016).
Ramos, S. N. D., Xavier, A. L. P., Teodoro, F. S., Gil, L. F. & Gurgel, L. V. A. Removal of cobalt(II), copper(II), and nickel(II) ions from aqueous solutions using phthalate-functionalized sugarcane bagasse: Mono- and multicomponent adsorption in batch mode. Ind Crop Prod 79, 116–130 (2016).
Palin, D. et al. Evaluation of Pb (II) biosorption utilizing sugarcane bagasse colonized by Basidiomycetes. Environ Monit Assess 188, 279 (2016).
Repo, E., Warchol, J. K., Bhatnagar, A., Mudhoo, A. & Sillanpaa, M. Aminopolycarboxylic acid functionalized adsorbents for heavy metals removal from water. Water Res 47, 4812–4832 (2013).
Article CAS PubMed Google Scholar
Zhao, F. P. et al. An EDTA-beta-cyclodextrin material for the adsorption of rare earth elements and its application in preconcentration of rare earth elements in seawater. J Colloid Interf Sci 465, 215–224 (2016).
Article ADS CAS Google Scholar
Wang, J. H. et al. Amino-functionalized Fe3O4@SiO2 core-shell magnetic nanomaterial as a novel adsorbent for aqueous heavy metals removal. J Colloid Interf Sci 349, 293–299 (2010).
Article ADS CAS Google Scholar
Deng, S. B. & Bai, R. B. Removal of trivalent and hexavalent chromium with aminated polyacrylonitrile fibers: performance and mechanisms. Water Res 38, 2424–2432 (2004).
Sheng, P. X., Ting, Y. P., Chen, J. P. & Hong, L. Sorption of lead, copper, cadmium, zinc, and nickel by marine algal biomass: characterization of biosorptive capacity and investigation of mechanisms. J Colloid Interf Sci 275, 131–141 (2004).
Article ADS CAS Google Scholar
Aksu, Z. Determination of the equilibrium, kinetic and thermodynamic parameters of the batch biosorption of nickel(II) ions onto Chlorella vulgaris. Process Biochem 38 (2012).
Li, Y. H. et al. Adsorption thermodynamic, kinetic and desorption studies of Pb2+ on carbon nanotubes. Water Res 39, 605–609 (2005).
Article CAS PubMed Google Scholar
Tokunaga, T. K., Kim, Y., Wan, J. M. & Yang, L. Aqueous Uranium(VI) Concentrations Controlled by Calcium Uranyl Vanadate Precipitates. Environ Sci Technol 46 (2012).
Nadeem, R. et al. Physical and chemical modification of distillery sludge for Pb(II) biosorption. J Hazard Mater 150, 335–342 (2008).
Article CAS PubMed Google Scholar
Abd El-Magied, M. O., Elshehy, E. A., Manaa, E. S. A., Tolba, A. A. & Atia, A. A. Kinetics and Thermodynamics Studies on the Recovery of Thorium Ions Using Amino Resins with Magnetic Properties. Ind Eng Chem Res 55, 11338–11345 (2016).
Chang, Y. H., Huang, C. F., Hsu, W. J. & Chang, F. C. Removal of Hg2+ from aqueous solution using alginate gel containing chitosan. J Appl Polym Sci 104, 2896–2905 (2007).
Atia, A. A., Donia, A. M. & Shahin, A. E. Studies on the uptake behavior of a magnetic Co3O4-containing resin for Ni(II), Cu(II) and Hg(II) from their aqueous solutions. Sep Purif Technol 46, 208–213 (2005).
Zou, Y. D. et al. beta-Cyclodextrin modified graphitic carbon nitride for the removal of pollutants from aqueous solution: experimental and theoretical calculation study. J Mater Chem A 4, 14170–14179 (2016).
Ahmad, A. L., Sumathi, S. & Hameed, B. H. Adsorption of residue oil from palm oil mill effluent using powder and flake chitosan: Equilibrium and kinetic studies. Water Res 39, 2483–2494 (2005).
Article CAS PubMed Google Scholar
Anderson, N. H. et al. Elucidating bonding preferences in tetrakis (imido) uranate (VI) dianions. Nature Chemistry, (2017).
Capretta, A., Maharajh, R. B. & Bell, R. A. Synthesis And Characterization Of Cyclomaltoheptaose-Based Metal Chelants as Probes for Intestinal Permeability. Carbohyd Res 267, 49–63 (1995).
Gunathilake, C., Gorka, J., Dai, S. & Jaroniec, M. Amidoxime-modified mesoporous silica for uranium adsorption under seawater conditions. J Mater Chem A 3, 11650–11659 (2015).
Wang, F. H. et al. A graphene oxide/amidoxime hydrogel for enhanced uranium capture. Sci Rep-Uk 6 (2016).
This work was supported by Natural Science Foundation of Heilongjiang Province (B2015021), Fundamental Research Funds of the Central University (HEUCFM), International Science & Technology Cooperation Program of China (2015DFR50050) and the Magor Project of Science and Technology of Heilongjiang Province (GA14A101).
Key Laboratory of Superlight Material and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin, 150001, P. R. China
Shouzheng Su, Jingyuan Liu, Rumin Li, Xiaoyan Jing & Jun Wang
Institute of Advanced Marine Materials, Harbin Engineering University, Harbin, 150001, P. R. China
Qi Liu & Jun Wang
Harbin Shipbuilding Engineering Design & Research Academy, Harbin, China
Qi Liu & Jun Wang
Modern Analysis, Test and Research Center, Heilongjiang University of Science and Technology, Harbin, 150027, P. R. China
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
S.Z.S. and J.W. contributed equally to this work. They conceived the idea, designed the experiments and wrote the paper. Q.L., J.Y.L. and H.S.Z. performed the material preparation, characterization, and adsorption tests. R.M.L. and X.Y.J. analyzed and interpreted the data. All authors discussed the results and commented on the manuscript.
Correspondence to Qi Liu or Jun Wang.
The authors declare that they have no competing interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
Su, S., Liu, Q., Liu, J. et al. Functionalized Sugarcane Bagasse for U(VI) Adsorption from Acid and Alkaline Conditions. Sci Rep 8, 793 (2018). https://doi.org/10.1038/s41598-017-18698-9
DOI: https://doi.org/10.1038/s41598-017-18698-9
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative
Environmental Science and Pollution Research (2020)
Environmental Science and Pollution Research (2019)
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.
Scientific Reports (Sci Rep) ISSN 2045-2322 (online)
Cas 351 35 9 Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.